中華人民共和國國家標準(中國大陸GB標準)英文版 |
GB標準是中華人民共和國國家標準,也叫GB國標,是中國大陸強制執行的國家標準,所有中國大陸境內銷售的商品及提供服務都必須符合GB國家標準的要求,包括進口商品及服務; 本網站提供GB國家標準的查詢檢索,英文版翻譯,GB標準產品檢測檢驗及合規性分析服務; |
GB/T 17737.201-2015 同轴通信电缆 第1-201部分:环境试验方法 电缆的冷弯性能试验(中英文版) Coaxial communication cables—Part 1-201: Environmental test methods—Test for cold bend performance of cable |
|||
GB/T 31489.1-2015 额定电压500kV及以下直流输电用挤包绝缘电力电缆系统 第1部分:试验方法和要求(中英文版) DC extruded cable systems for power transmission at a rated voltage up to and including 500kV―Part 1: Test methods and requirements |
|||
GB/T 3780.1-2015 炭黑 第1部分:吸碘值试验方法(中英文版) Carbon black—Part 1:Test method for iodine adsorption number |
|||
GB/T 5594.8-2015 电子元器件结构陶瓷材料性能测试方法 第8部分:显微结构的测定方法(中英文版) Test methods for properties of structure ceramic used in electronic components and device—Part 8: Test method for microstructure |
|||
GB/T 5211.18-2015 颜料和体质颜料通用试验方法 第18部分:筛余物的测定 水法(手工操作)(中英文版) General methods of test for pigments and extenders—Part 18: Determination of residue on sieve—Water method (Manual procedure) |
|||
GB/T 31467.3-2015 电动汽车用锂离子动力蓄电池包和系统 第3部分:安全性要求与测试方法(中英文版) Lithium-ion traction battery pack and system for Electric vehicles—Part 3: Safety requirements and test methods |
|||
GB/T 5594.4-2015 电子元器件结构陶瓷材料性能测试方法 第4部分:介电常数和介质损耗角正切值的测试方法(中英文版) Test methods for properties of structure ceramic used in electronic components and device—Part 4: Test method for permittivity and dielectric loss angle tangent value |
|||
GB/T 5594.7-2015 电子元器件结构陶瓷材料性能测试方法 第7部分:透液性测定方法(中英文版) Test methods for properties of structure ceramic used in electronic components and device—Part 7: Test method for liquid permeability |
|||
GB/T 5838.3-2015 荧光粉 第3部分:性能试验方法(中英文版) Phosphors—Part 3: Test methods for properties |
|||
GB/T 5594.6-2015 电子元器件结构陶瓷材料性能测试方法 第6部分:化学稳定性测试方法(中英文版) Test methods for properties of structure ceramics used in eletronic components and device—Part 6: Test method for chemical durability |
|||
GB/T 5594.3-2015 电子元器件结构陶瓷材料性能测试方法 第3部分:平均线膨胀系数测试方法(中英文版) Test methods for properties of structure ceramic used in electronic components and device—Part 3: Test method for mean coefficient of linear expansion |
|||
GB/T 18488.2-2015 电动汽车用驱动电机系统 第2部分:试验方法(中英文版) Drive motor system for electric vehicles—Part 2: Test methods |
|||
GB/T 17614.2-2015 工业过程控制系统用变送器 第2部分:检查和例行试验方法(中英文版) Transmitters for use in industrial-process control systems—Part 2: Methods for inspection and roution testing |
|||
GB/T 30032.1-2015 移动式升降工作平台 带有特殊部件的设计、计算、安全要求和试验方法 第1部分:装有伸缩式护栏系统的移动式升降工作平台(中英文版) Mobile elevating work platforms—Design, calculations, safety requirements and test methods relative to special features—Part 1: MEWPs with retractable guardrail systems |
|||
GB/T 31334.1-2015 浸胶帆布试验方法 第1部分:粘合强度(中英文版) Test methods for dipped canvas—Part 1: Adhesion strength |
|||
GB/T 31334.2-2015 浸胶帆布试验方法 第2部分:经向卷曲度和密度(中英文版) Test methods for dipped canvas—Part 2: Yarn crimp on warp and density |
|||
GB/T 31334.3-2015 浸胶帆布试验方法 第3部分:硬挺度(中英文版) Test methods for dipped canvas—Part 3: Stiffness |
|||
GB/T 24218.18-2014 纺织品 非织造布试验方法 第18部分:断裂强力和断裂伸长率的测定(抓样法)(中英文版) Textiles―Test methods for nonwovens―Part 18: Determination of breaking strength and elongation (grab method) |
|||
GB/T 6324.6-2014 有机化工产品试验方法 第6部分:液体色度的测定 三刺激值比色法(中英文版) Test method of organic chemical products—Part 6: Determination of color for liquids—Tristimulus colorimetry |
|||
GB/T 8117.3-2014 汽轮机热力性能验收试验规程 第3部分:方法C 改造汽轮机的热力性能验证试验(中英文版) Rules for steam turbine thermal acceptance test―Part 3: Method C―Thermal performance verification tests of retrofitted steam turbines |
|||
GB/T 22148.2-2014 电磁发射的试验方法 第2部分:放电灯(荧光灯除外)用电子控制装置(中英文版) Test method on electromagnetic emissions―Part 2: Electronic control gear for discharge lamps excluding fluorescent lamps |
|||
GB/T 25151.6-2014 尿素高压设备制造检验方法 第6部分:尿素高压设备氦渗漏试验方法(中英文版) Fabrication and inspection method for high pressure urea equipment―Part 6: Helium leakage test method for urea high pressure equipment |
|||
GB/T 22148.1-2014 电磁发射的试验方法 第1部分:单端和双端荧光灯用电子控制装置(中英文版) Test method on electromagnetic emissions―Part 1: Electronic control gear for single-and double-capped fluorescent lamps |
|||
GB/T 4372.6-2014 直接法氧化锌化学分析方法 第6部分:金属锌的检验(中英文版) Methods for chemical analysis of zincoxide produced by direct process―Part 6:Testing of metallic zinc |
|||
GB/T 12967.4-2014 铝及铝合金阳极氧化膜检测方法 第4部分:着色阳极氧化膜耐紫外光性能的测定(中英文版) Test methods for anodic oxidation coatings of aluminium and aluminium alloys―Part 4:Determination of the comparative fastness to ultraviolet light and heat of coloured anodic oxidation coatings |
|||
GB/T 10066.3-2014 电热装置的试验方法 第3部分:有心感应炉和无心感应炉(中英文版) Test methods for electroheat installations―Part 3: Induction channel and induction crucible furnaces |
|||
GB/T 2424.12-2014 环境试验 第2部分:试验方法 试验Kd:接触点和连接件的硫化氢试验导则(中英文版) Environmental testing—Part 2: Test methods—Guidance to test Kd: Hydrogen sulphide test for contacts and connections |
|||
GB/T 2423.20-2014 环境试验 第2部分:试验方法 试验Kd:接触点和连接件的硫化氢试验(中英文版) Environmental testing—Part 2:Test methods—Test Kd: Hydrogen sulphide test for contacts and connections |
|||
GB/T 22517.10-2014 体育场地使用要求及检验方法 第10部分:壁球场地(中英文版) Technical requirements and test methods for sports field—Part 10: Squash |
|||
GB/T 31213.2-2014 无损检测 铸铁构件检测 第2部分:声超声检测方法(中英文版) Non-destructive testing―Testing of cast iron equipments and components―Part 2: Test method for acousto-ultrasonic |
|||
GB/T 22517.11-2014 体育场地使用要求及检验方法 第11部分:曲棍球场地(中英文版) Technical requirements and test methods for sports field―part 11: Hockey |
|||
GB/T 10066.5-2014 电热装置的试验方法 第5部分:电热和电化学用等离子体设备(中英文版) Test methods for electroheat installations—Part 5:Plasma equipment for electroheat and electrochemical applications |
|||
GB/T 13465.1-2014 不透性石墨材料试验方法 第1部分:力学性能试验方法总则(中英文版) Test method of impermeable graphite materials―Part 1: General 0f test method for mechanical properties |
|||
GB/T 5169.38-2014 电工电子产品着火危险试验 第38部分:燃烧流的毒性 试验方法概要和相关性(中英文版) Fire hazard testing for electric and electronic products―Part 38: Toxicity of fire effluent―Summary and relevance of test methods |
|||
GB/T 31213.1-2014 无损检测 铸铁构件检测 第1部分:超声检测方法(中英文版) Non-destructive testing—Testing of cast iron equipments and components―Part 1: Test method for ultrasonic |
|||
GB/T 31213.3-2014 无损检测 铸铁构件检测 第3部分:声发射检测方法(中英文版) Non-destructive testing—Testing of cast iron equipments and components—Part 3: Test method for acoustic emission |
|||
GB/Z 5169.34-2014 电工电子产品着火危险试验 第34部分:着火危险评定导则 起燃性 试验方法概要和相关性(中英文版) Fire hazard testing for electric and eletronic products—Part 34: Guidance for assessing the fire hazard—Ignitability—Summary and relevance of test methods |
|||
GB/T 11017.1-2014 额定电压110kV(Um=126kV)交联聚乙烯绝缘电力电缆及其附件 第1部分:试验方法和要求(中英文版) Power cables with cross-linked polyethylene insulation and their accessories for rated voltage of 110 kV(Um=126 kV)―Part 1: Test methods and requirements |
|||
GB/T 30968.4-2014 聚合物基复合材料层合板开孔/受载孔性能试验方法 第4部分:开孔压缩强度试验方法(中英文版) Test method for open-hole/loaded-hole of polymer matrix composite laminates―Part 4: Test method of open-hole compressive strength |
|||
GB/T 30968.3-2014 聚合物基复合材料层合板开孔/受载孔性能试验方法 第3部分:开孔拉伸强度试验方法(中英文版) Test method for open-hole/loaded-hole of polymer matrix composite laminates―Part 3: Test method of open-hole tensile strength strength |
|||
GB/T 30968.2-2014 聚合物基复合材料层合板开孔/受载孔性能试验方法 第2部分:充填孔拉伸和压缩试验方法(中英文版) Test method for open-hole/loaded-hole of polymer matrix composite laminates―Part 2: Test method of filled-hole tension and compression |
|||
GB/T 30968.1-2014 聚合物基复合材料层合板开孔/受载孔性能试验方法 第1部分:挤压性能试验方法(中英文版) Test method for open-hole/loaded-hole of polymer matrix composite laminates—Part 1: Test method of bearing response |
|||
GB/T 19933.4-2014 土方机械 司机室环境 第4部分:采暖、换气和空调(HVAC)的试验方法和性能(中英文版) Earth-Earth-moving machinery―Operator enclosure environment―Part 4: Heating, ventilation and air conditioning (HVAC) test method and performance |
|||
GB/T 5211.15-2014 颜料和体质颜料通用试验方法 第15部分:吸油量的测定(中英文版) General methods of test for pigments and extenders―Part 15:Determination of oil absorption value |
|||
GB/T 30921.1-2014 工业用精对苯二甲酸(PTA)试验方法 第1部分:对羧基苯甲醛(4-CBA)和对甲基苯甲酸(p-TOL)含量的测定(中英文版) Test method of purified terephthalic acid (PTA) for industrial use―Part 1:Determination of concentrations of 4-carboxybenzaldehyde (4-CBA) and p-toluic acid (p-TOL) |
|||
GB/T 30790.6-2014 色漆和清漆 防护涂料体系对钢结构的防腐蚀保护 第6部分:实验室性能测试方法(中英文版) Paints and varnishes―Corrosion protection of steel structures by protective paint systems―Part 6: Laboratory performance test methods |
|||
GB/T 25206.1-2014 复合夹芯板建筑体燃烧性能试验 第1部分:小室法(中英文版) Reaction-to-fire tests for sandwich panel building systems―Part 1: Test method for small rooms |
|||
GB/T 30268.1-2013 信息技术 生物特征识别应用程序接口(BioAPI)的符合性测试 第1部分:方法和规程(中英文版) Information technology—Conformance testing for the biometric application programming interface (BioAPI)—Part 1: Methods and procedures |
|||
GB/T 30202.5-2013 脱硫脱硝用煤质颗粒活性炭试验方法 第5部分:脱硝率(中英文版) Test method for coal-based granular activated carbon for desulfurization and denitration process―Part 5:Denitration value |
|||
GB/T 5169.20-2013 电工电子产品着火危险试验 第20部分:火焰表面蔓延 试验方法概要和相关性(中英文版) Fire hazard testing for electric and electronic products—Part 20: Surface spread of flame—Summary and relevance of test methods |
|||
GB/T 30475.1-2013 压缩空气过滤器 试验方法 第1部分:悬浮油(中英文版) Filters for compressed air―Test methods―Part 1: Oil aerosols |
|||
GB/T 11446.9-2013 电子级水中微粒的仪器测试方法(中英文版) Test method for particles in electronic grade water by instrument |
|||
GB/T 30202.1-2013 脱硫脱硝用煤质颗粒活性炭试验方法 第1部分:堆积密度(中英文版) Test method for granular activated carbon from coal for desulfurization and denitration process―Part 1: Bulk density |
|||
GB/T 30202.2-2013 脱硫脱硝用煤质颗粒活性炭试验方法 第2部分:粒度(中英文版) Test method for granular coal-based activated carbon for desulfurization and denitration process―Part 2: Particle size |
|||
GB/T 30202.4-2013 脱硫脱硝用煤质颗粒活性炭试验方法 第4部分:脱硫值(中英文版) Test method for granular activated carbonfrom coal for desulfurization and denitration process―Part 4: Desulfurization value |
|||
GB/T 30202.3-2013 脱硫脱硝用煤质颗粒活性炭试验方法 第3部分:耐磨强度、耐压强度(中英文版) Test method for granular activated carbon from coal for desulfurization and denitration process―Part3: Abrasive resistance and compression strength |
|||
GB/T 30475.2-2013 压缩空气过滤器 试验方法 第2部分:油蒸气(中英文版) Filters for compressed air― Test methods―Part 2: Oil vapours |
|||
GB/T 30103.1-2013 冷库热工性能试验方法 第1部分:温度和湿度检测(中英文版) Methods of testing for thermal performance on cold store―Part 1: Temperature and humidity testing |
|||
GB/T 5169.13-2013 电工电子产品着火危险试验 第13部分:灼热丝/热丝基本试验方法 材料的灼热丝起燃温度(GWIT)试验方法(中英文版) Fire hazard testing for electric and electronic product―Part 13:Glowing/hot-wire based test methods―Glow-wire ignition temperature (GWIT) test method for materials |
|||
GB/T 30103.3-2013 冷库热工性能试验方法 第3部分:围护结构热流量检测(中英文版) Methods of testing for thermal performance on cold store―Part 3: Heat flux testing for envelope enclosure |
|||
GB/T 30177.1-2013 过滤机性能测试方法 第1部分:加压过滤机(中英文版) Methods of perfomance testing for filters―Part 1:Press filter |
|||
GB/T 30103.2-2013 冷库热工性能试验方法 第2部分:风速检测(中英文版) Methods of testing for thermal performance on cold store―Part 2: Air velocity testing |
|||
GB/T 5169.12-2013 电工电子产品着火危险试验 第12部分:灼热丝/热丝基本试验方法 材料的灼热丝可燃性指数(GWFI)试验方法(中英文版) Fire hazard testing for electric and electronic products―Part 12: Glowing/hot-wire based test methods―Glow-wire flammability index (GWFI) test method for materials |
|||
GB/T 30040.7-2013 双层罐渗漏检测系统 第7部分:双层间隙、防渗漏衬里及防渗漏外套的一般要求和试验方法(中英文版) Leak detection systems―Part 7:General requirements and test methods for interstitial spaces,leak protecting linings and leak protecting jacket |
|||
GB/T 7689.4-2013 增强材料 机织物试验方法 第4部分:弯曲硬挺度的测定(中英文版) Reinforcements - Test method for woven fabrics - Part 4: Determination of flexural stiffness |
|||
GB/T 30032.2-2013 移动式升降工作平台 带有特殊部件的设计、计算、安全要求和试验方法 第2部分:装有非导电(绝缘)部件的移动式升降工作平台(中英文版) Mobile elevating work platforms - Design, calculations,safety requirements and test methods relative to special features - Part 2: MEWPs with non-conductive (insulating)components |
|||
GB/T 12967.5-2013 铝及铝合金阳极氧化膜检测方法 第5部分:用变形法评定阳极氧化膜的抗破裂性(中英文版) Test methods for anodic oxidation coatings of aluminium and aluminium alloys - Part 5:Assessment of resistance of anodic oxidation coatings to cracking by deformation |
|||
GB/T 27797.4-2013 纤维增强塑料 试验板制备方法 第4部分:预浸料模塑(中英文版) Fibre-reinforced plastics - Methods of producing test plates - Part 4:Moulding of prepregs |
|||
GB/T 7689.1-2013 增强材料 机织物试验方法 第1部分:厚度的测定(中英文版) Reinforcements - Test method for woven fabrics - Part 1:Determination of thickness |
|||
GB/T 7689.3-2013 增强材料 机织物试验方法 第3部分:宽度和长度的测定(中英文版) Reinforcements - Test method for woven fabrics - Part 3: Determination of width and length |
|||
GB/T 7689.5-2013 增强材料 机织物试验方法 第5部分:玻璃纤维拉伸断裂强力和断裂伸长的测定(中英文版) Reinforcements - Test method for woven fabrics - Part 5: Determination of glass fibre tensile breaking force and elongation at break |
|||
GB/T 7690.1-2013 增强材料 纱线试验方法 第1部分:线密度的测定(中英文版) Reinforcements - Test method for yarns - Part 1: Determination of linear density |
|||
GB/T 7690.2-2013 增强材料 纱线试验方法 第2部分:捻度的测定(中英文版) Reinforcements - Test method for yarns - Part 2: Determination of twist |
|||
GB/T 7690.3-2013 增强材料 纱线试验方法 第3部分:玻璃纤维断裂强力和断裂伸长的测定(中英文版) Reinforcements - Test method for yarns - Part 3: Determination of breaking force and breaking elongation for glass fibre |
|||
GB/T 9914.2-2013 增强制品试验方法 第2部分:玻璃纤维可燃物含量的测定(中英文版) Test method for reinforcement products - Part 2: Determination of combustible-matter content for glass fibre |
|||
GB/T 9914.1-2013 增强制品试验方法 第1部分:含水率的测定(中英文版) Test method for reinforcement products - Part 1: Determination of moisture content |
|||
GB/T 29882-2013 杂项危险物质和物品分类试验方法 正辛醇/水分配系数(中英文版) Testing method for classification of hazardous materials - Partition coefficient of 1-octanol/water |
|||
GB/T 27748.2-2013 固定式燃料电池发电系统 第2部分:性能试验方法(中英文版) Stationary fuel cell power systems - part 2: Performance test methods |
|||
GB/T 2423.24-2013 环境试验 第2部分:试验方法 试验Sa:模拟地面上的太阳辐射及其试验导则(中英文版) Environmental testing - Part 2: Test methods - Test Sa: Simulated solar radiation at ground level and guidance for solar radiation testing |
|||
GB/T 2423.19-2013 环境试验 第2部分:试验方法 试验Kc:接触点和连接件的二氧化硫试验(中英文版) Environmental testing - Part 2: Test methods - Test Kc: Sulphur dioxide test for contacts and connections |
|||
GB/T 2424.11-2013 环境试验 第2部分:试验方法 试验Kc:接触点和连接件的二氧化硫试验导则(中英文版) Environmental testing - Part 2: Test methods - Guidance to test Kc: Sulphur dioxide test for contacts and connections |
|||
GB/T 30001.5-2013 信息技术 基于射频的移动支付 第5部分:射频接口测试方法(中英文版) Information technology - RF-based mobile payment - Part 5: Test methods of radio frequency interface |
|||
GB/T 6006.3-2013 玻璃纤维毡试验方法 第3部分:厚度的测定(中英文版) Test method for glass mats - Part 3:Determination of thickness |
|||
GB/T 6006.2-2013 玻璃纤维毡试验方法 第2部分:拉伸断裂强力的测定(中英文版) Test method for glass mats - Part 2: Determination of tensile breaking force |
|||
GB/T 6006.1-2013 玻璃纤维毡试验方法 第1部分:苯乙烯溶解度的测定(中英文版) Test method for glass mats - Part 1: Determination of styrene solubility |
|||
GB/T 7690.4-2013 增强材料 纱线试验方法 第4部分:硬挺度的测定(中英文版) Reinforcements - Test method for yarns - Part 4: Determination of stiffness |
|||
GB/T 7690.6-2013 增强材料 纱线试验方法 第6部分:捻度平衡指数的测定(中英文版) Reinforcements - Test method for yarns - Part 6: Determination of twist balance index |
|||
GB/T 7690.5-2013 增强材料 纱线试验方法 第5部分:玻璃纤维纤维直径的测定(中英文版) Reinforcements - Test method for yarns - Part 5:Determination of fiber diameter for glass fiber |
|||
GB/T 7689.2-2013 增强材料 机织物试验方法 第2部分:经、纬密度的测定(中英文版) Reinforcements - Test method for woven fabrics - Part 2: Determination of number of yarns per unit length of warp and weft |
|||
GB/T 20629.2-2013 电气用非纤维素纸 第2部分:试验方法(中英文版) Non-cellulosic paper for electrical purposes - Part 2:Methods of test |
|||
GB/T 19264.2-2013 电气用压纸板和薄纸板 第2部分:试验方法(中英文版) Pressboard and presspaper for electrical purposes - Part 2: Methods of test |
|||
GB/T 16903.3-2013 标志用图形符号表示规则 第3部分:感知性测试方法(中英文版) Rules for the presentation of graphical symbols for use on graphical signs - Part 3: Method for testing perceptibility |
|||
GB/T 16903.2-2013 标志用图形符号表示规则 第2部分:理解度测试方法(中英文版) Rules for the presentation of graphical symbols for use on graphical signs - Part 2: Methods for testing comprehensibility |
|||
GB/T 29627.2-2013 电气用聚芳酰胺纤维纸板 第2部分:试验方法(中英文版) Aramid pressboard for electrical purposes - Part 2: Methods of test |
|||
GB/T 29235.2-2012 接入设备节能参数和测试方法 第2部分:ADSL局端(中英文版) Energy efficiency metrologies and test methods for access equipments - Part 2: ADSL DSLAM |
|||
GB/T 29459.1-2012 在役承压设备金属材料小冲杆试验方法 第1部分:总则(中英文版) Small punch test methods of metallic materials for in-service pressure equipments - Part 1:General requirements |
|||
GB/T 29459.2-2012 在役承压设备金属材料小冲杆试验方法 第2部分:室温下拉伸性能的试验方法(中英文版) Small punch test methods of metallic materials for in-service pressure equipments - Part 2:Method of test for tensile properties at room temperature |
|||
GB/T 18029.14-2012 轮椅车 第14部分:电动轮椅车和电动代步车动力和控制系统 要求和测试方法(中英文版) Wheelchairs - Part 14: Power and control systems for electrically powered wheelchairs and scooter - Requirements and test methods |
|||
GB/T 18029.24-2012 轮椅车 第24部分:乘坐者操纵的爬楼梯装置的要求和测试方法(中英文版) Wheelchairs - Part 24:Requirements and test methods for user-operated stair climbing devices |
|||
GB/T 11417.5-2012 眼科光学 接触镜 第5部分: 光学性能试验方法(中英文版) Ophthalmic optics - Contact lenses - Part 5: Testing methods for optical properties |
|||
GB/T 29235.1-2012 接入设备节能参数和测试方法 第1部分:ADSL用户端(中英文版) Energy efficiency metrology and test methods for access equipments - Part 1:ADSL CPE |
|||
GB/T 29268.2-2012 信息技术 生物特征识别性能测试和报告 第2部分:技术与场景评价的测试方法(中英文版) Information technology - Biometric performance testing and reporting - Part 2: Testing methodologies for technology and scenario evaluation |
|||
GB/T 29200-2012 公用电信网设备安全测试方法 主叫用户号码信息(中英文版) Test method for public telecommunication network equipments security - Calling party number information |
|||
GB/T 14999.2-2012 高温合金试验方法 第2部分:横向低倍组织及缺陷酸浸检验(中英文版) Test methods for superalloys - Part 2: Verification of transverse macro-structures and defect by etch |
|||
GB/T 14999.1-2012 高温合金试验方法 第1部分:纵向低倍组织及缺陷酸浸检验(中英文版) Test method for superalloys - Part 1: Verification of longitudinal macro-structures and defect by etch |
|||
GB/T 15623.3-2012 液压传动 电调制液压控制阀 第3部分:压力控制阀试验方法(中英文版) Hydraulic fluid power - Electrically modulated hydraulic control valves - Part 3: Test methods for pressure control valves |
|||
GB/T 2423.50-2012 环境试验 第2部分:试验方法 试验Cy: 恒定湿热 主要用于元件的加速试验(中英文版) Environmental testing - Part 2: Test methods - Test Cy: Damp heat,steady state,accelerated test primarily intended for components |
|||
GB/T 14999.4-2012 高温合金试验方法 第4部分:轧制高温合金条带晶粒组织和一次碳化物分布测定(中英文版) Test methods for superalloys - Part 4: Determination of characterizing banding grains and primary carbides distribution of superalloy rollings |
|||
GB/T 4857.23-2012 包装 运输包装件基本试验 第23部分: 随机振动试验方法(中英文版) Packaging - Basic tests for transport packages - Part 23:Random vibration test method |
|||
GB 10810.4-2012 眼镜镜片 第4部分:减反射膜规范及测量方法(中英文版) Uncut finished spectacle lenses - Part 4: Specifications and test methods for anti-reflective coatings |
|||
GB/T 2820.11-2012 往复式内燃机驱动的交流发电机组 第11部分:旋转不间断电源 性能要求和试验方法(中英文版) Reciprocating internal combustion engine driven alternating current generating sets - Part 11: Rotary uninterruptible power systems - Performance requirements and test methods |
|||
GB/T 14999.3-2012 高温合金试验方法 第3部分:棒材纵向断口检验(中英文版) Test methods for superalloys - Part 3: Verification of longitudinal fracture of bars |
|||
GB/T 18029.21-2012 轮椅车 第21部分:电动轮椅车、电动代步车和电池充电器的电磁兼容性要求和测试方法(中英文版) Wheelchairs - Part 21: Requirements and test methods for electromagnetic compatibility of electrically powered wheelchairs and scooters, and battery chargers |
|||
GB/T 24218.12-2012 纺织品 非织造布试验方法 第12部分:受压吸收性的测定(中英文版) Textiles - Test methods for nonwovens - Part 12:Demand absorbency |
|||
GB/T 24218.11-2012 纺织品 非织造布试验方法 第11部分:溢流量的测定(中英文版) Textiles - Test methods for nonwovens - Part 11: Run-off |
|||
GB/T 25749.7-2012 机械安全 空气传播的有害物质排放的评估 第7部分:测量污染物浓度参数的试验台法(中英文版) Safety of machinery - Evaluation of the emission of airborne hazardous substances - Part 7: Test bench method for the measurement of the pollutant concentration parameter |
|||
GB/T 8243.9-2012 内燃机全流式机油滤清器试验方法 第9部分:进、出口止回阀试验(中英文版) Methods of test for full-flow lubricating oil filters for internal combustion engines - Part 9: Inlet and outlet anti-drain valve tests |
|||
GB/T 25749.6-2012 机械安全 空气传播的有害物质排放的评估 第6部分:测量带导管出口的空气净化系统质量分离效率的试验台法(中英文版) Safety of machinery - Evaluation of the emission of airborne hazardous substances - Part 6: Test bench method for the measurement of the separation efficiency by mass of air cleaning systems with ducted outlet |
|||
GB/T 25749.5-2012 机械安全 空气传播的有害物质排放的评估 第5部分:测量不带导管出口的空气净化系统质量分离效率的试验台法(中英文版) Safety of machinery - Evaluation of the emission of airborne hazardous substances - Part 5: Test bench method for the measurement of the separation efficiency by mass of air cleaning systems with unducted outlet |
|||
GB/T 27698.2-2011 热交换器及传热元件性能测试方法 第2部分:管壳式热交换器(中英文版) Test method for the performance of heat exchangers and heat exchange element - Part 2: Tubular heat exchanger |
|||
GB/T 27797.7-2011 纤维增强塑料 试验板制备方法 第7部分:树脂传递模塑(中英文版) Fibre-reinforced plastics - Methods of producing test plates - Part 7: Resin transfer moulding |
|||
GB/T 27698.6-2011 热交换器及传热元件性能测试方法 第6部分:空冷器用翅片管(中英文版) Test method for the performance of heat exchangers and heat exchange element - Part 6: Fing tube for air-cooled heat exchangers |
|||
GB/T 27698.7-2011 热交换器及传热元件性能测试方法 第7部分:空冷器噪声测定(中英文版) Test method for the performance of heat exchangers and heat exchange element - Part 7: Measurement of noise from air-cooled heat exchangers |
|||
GB/T 27698.5-2011 热交换器及传热元件性能测试方法 第5部分:管壳式热交换器用换热管(中英文版) Test method for the performance of heat exchangers and heat exchange element - Part 5: Heat transfer tube for tubular heat exchangers |
|||
GB/T 27698.4-2011 热交换器及传热元件性能测试方法 第4部分:螺旋板式热交换器(中英文版) Test method for the performance of heat exchangers and heat exchange element - Part 4: Spiral heat exchanger |
|||
GB/T 27698.3-2011 热交换器及传热元件性能测试方法 第3部分:板式热交换器(中英文版) Test method for the performance of heat exchangers and heat exchange element - Part 3: Plate heat exchanger |
|||
GB/T 27698.1-2011 热交换器及传热元件性能测试方法 第1部分:通用要求(中英文版) Test method for the performance of heat exchangers and heat exchange element - Part 1: General requirements |
|||
GB/T 17178.7-2011 信息技术 开放系统互连 一致性测试方法和框架 第7部分:实现一致性声明(中英文版) Information technology - Open systems interconnection - Conformance testing methodology and framework - Part 7: Implementation conformance statements |
|||
GB/T 17178.5-2011 信息技术 开放系统互连 一致性测试方法和框架 第5部分: 一致性评估过程对测试实验室及客户的要求(中英文版) Information technology - Open systems interconnection - Conformance testing methodology and framework - Part 5: Requirement on test laboratories and clients for the conformance assessment process |
|||
GB 27934.1-2011 纸质印刷品覆膜过程控制及检测方法 第1部分:基本要求(中英文版) Lamination process control and testing methods for paper prints - Part 1: General requirements |
|||
GB/T 22517.6-2011 体育场地使用要求及检验方法 第6部分:田径场地(中英文版) Technical requirements and test methods for sports filed - Part 6: Track and field |
|||
GB/T 27623.1-2011 渔用抗菌药物药效试验技术规范 第1部分:常量肉汤稀释法药物敏感性试验(中英文版) Pharmacodynamic test technical specification for aquaculture antimicrobial agent - Part 1: Antibiotics susceptibility test of macro-broth dilution method |
|||
GB/T 27698.8-2011 热交换器及传热元件性能测试方法 第8部分:热交换器工业标定(中英文版) Test method for the performance of heat exchangers and heat exchange element - Part 8: Determination of industrial locale for heat exchangers |
|||
GB/T 20633.2-2011 承载印制电路板用涂料(敷形涂料) 第2部分:试验方法(中英文版) Coatings for loaded printed wire boards (conformal coatings) - Part 2:Methods of test |
|||
GB/T 27797.2-2011 纤维增强塑料 试验板制备方法 第2部分:接触和喷射模塑(中英文版) Fibre-reinforced plastics - Methods of producing test plates - Part 2: Contact and spray-up moulding |
|||
GB/T 18570.6-2011 涂覆涂料前钢材表面处理 表面清洁度的评定试验 第6部分:可溶性杂质的取样 Bresle法(中英文版) Preparation of steel substrates before application of paints and related products -Tests for the assessment of surface cleanliness - Part6: Extraction of soluble contaminants for analysis -The Bresle method |
|||
GB/T 27797.9-2011 纤维增强塑料 试验板制备方法 第9部分:GMT/STC模塑(中英文版) Fibre-reinforced plastics - Methods of producing test plates - Part 9:Moulding of GMT/STC |
|||
GB/T 27797.8-2011 纤维增强塑料 试验板制备方法 第8部分:SMC及BMC模塑(中英文版) Fibre-reinforced plastics - Methods of producing test plates - Part 8: Compression moulding of SMC and BMC |
|||
GB/T 27934.2-2011 纸质印刷品覆膜过程控制及检测方法 第2部分:乙烯-醋酸乙烯共聚物(EVA)热熔胶预涂覆膜(中英文版) Lamination process control and testing methods for paper prints - Part 2: Lamination with EVA adhesive |
|||
GB/T 27797.6-2011 纤维增强塑料 试验板制备方法 第6部分:拉挤模塑(中英文版) Fibre-reinforced plastics - Methods of producing test plates - Part 6: Pultrusion moulding |
|||
GB/T 27797.5-2011 纤维增强塑料 试验板制备方法 第5部分:缠绕成型(中英文版) Fibre-reinforced plastics - Methods of producing test plates - Part 5: Filament winding |
|||
GB/T 27797.3-2011 纤维增强塑料 试验板制备方法 第3部分:湿法模塑(中英文版) Fibre-reinforced plastics - Methodsof producing test plates - Part 3: Wet compression moulding |
|||
GB/T 27797.1-2011 纤维增强塑料 试验板制备方法 第1部分:通则(中英文版) Fibre-reinforced plastics - Methods of producing test plates - Part 1: General conditions |
|||
GB/T 27797.11-2011 纤维增强塑料 试验板制备方法 第11部分:BMC和其他长纤维模塑料注射模塑 小方片(中英文版) Fibre-reinforced plastics - Methods of producing test plates - Part 11: Injection moulding of BMC and other long-fibre moulding compounds - Small plates |
|||
GB/T 27797.10-2011 纤维增强塑料 试验板制备方法 第10部分:BMC和其他长纤维模塑料注射模塑 一般原理和通用试样模塑(中英文版) Fibre-reinforced plastics - Methods of producing test plates - Part 10: Injection moulding of BMC and other long-fibre moulding compounds - General principles and moulding of multipurpose test specimens |
|||
GB/T 27845-2011 化学品 土壤粒度分析试验方法(中英文版) Chemicals - Test method for particle-size analysis of soils |
|||
GB/T 27934.4-2011 纸质印刷品覆膜过程控制及检测方法 第4部分:反应型聚氨酯(PUR)热熔胶即涂覆膜(中英文版) Lamination process control and testing methods for paper prints - Part 4: Lamination with polyurethane reactive hot melt adhesive |
|||
GB/T 27934.3-2011 纸质印刷品覆膜过程控制及检测方法 第3部分:水基胶黏剂即涂干式覆膜(中英文版) Lamination process control and testing methods for paper prints - Part 3: Drying lamination with water-based adhesive |
|||
GB/T 20485.31-2011 振动与冲击传感器的校准方法 第31部分:横向振动灵敏度测试(中英文版) Methods for the calibration of vibration and shock transducers - Part 31: Testing of transverse vibration sensitivity |
|||
GB/T 26948.1-2011 工业车辆驾驶员约束系统技术要求及试验方法 第1部分:腰部安全带(中英文版) Industrial trucks - Specifications and test methods for operator restraint systems - Part 1:Lap-type seat belts |
找到:1001條目 | [首頁]-[上一頁]-[下一頁]-[尾頁] | 去到: 1 2 3 4 5 6 7 |